ASTM D5084 FREE DOWNLOAD

The schematic of the hydraulic system in Fig. Measure and record, to a minimum of three signi? Where the sampling operation has caused disturbance of the soil, the disturbed material shall be trimmed. Agencies that meet the criteria of Practice D are generally considered capable of competent and objective testing, sampling, inspection, etc.. Other items, such as use of higher hydraulic gradients, lower viscosity? The head loss across the permeameter shall be measured to a minimum of three signi? The diameter and height of the specimen shall each be at least 6 times greater than the largest particle size within the specimen.

Uploader:	Kekus
Date Added:	18 April 2015
File Size:	32.49 Mb
Operating Systems:	Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X
Downloads:	98408
Price:	Free* [*Free Regsitration Required]

Distilled water can signi? Falling head tests may be performed with either a constant tailwater elevation Method B or a rising tailwater elevation Method Csee Fig. The specimen may swell when exposed to water; the effective stress will tend to counteract the swelling.

ASTM D, Test equipment Controls

Agencies that meet the criteria of Practice D are generally considered capable of competent and objective testing, sampling, inspection, etc. The development of the hydraulic conductivity equation for this type of system is given in Appendix X1. Typically a test can be performed using Methods D, E, or F within two to three days. NOTE 13—When the water pressure in a test specimen changes and the applied total stress is constant, the effective stress in the test specimen changes, which can cause volume changes that can invalidate the test results.

Reliable results depend on many factors; Practice D provides a means of evaluating some of those factors. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Then, apply the same air pressure to these two burettes.

Data acquisition is r5084 in the load frame; four channels are available for load, displacement, pore pressure and volume change. Properly sized tubing, etc. In addition, the ratio of initial head loss divided by? There astk six alternate methods or hydraulic systems that may be used to measure the hydraulic conductivity.

For normally consolidated soils: Agencies that meet the criteria of Practice D are generally considered capable of competent and objective testing, sampling, inspection, etc.

ASTM D5084

NOTE 15—The interval of time, Dt, can be measured directly using a stop watch or equivalent device, see If such a room is not available, the apparatus shall be placed in a water bath, insulated chamber, or other device that maintains a temperature within asttm tolerance speci? Properly shortening the length or enlarging the cross-sectional area, or both, of the test specimen.

Other strategies, such as using higher viscosity fluid or properly decreasing the cross-sectional area of the test specimen, or both, may also be possible. In each of these systems, the mercury-? In addition, there is continuity of in? The membrane shall be carefully inspected prior to use. Apply back pressure by simultaneously increasing the cell pressure and the in? If it is not, there is an error in applying equal pressures ashm the two tubes of the U-tube manometer, check for air in the lines, external pressure source, etc.

The procedures used do not consider material variation, purpose for obtaining the data, special purpose studies, or any considerations for the user's objectives; and it is common practice to increase or reduce significant digits of reported data to be commensurate with these considerations.

TRITECH original high-performance load frames for triaxial tests, ideal solution for advanced and research laboratories that perform high quality tests at high productivity levels. By tradition in U. Hydraulic conductivity varies with varying void ratio, which changes when the effective stress changes. Also, measurements in the change in height of the test specimen, coupled with knowledge of the initial height, provide a means for checking the?

In atm system shown in Fig. The inch-pound units given in parentheses are mathematical conversions, which are provided for information purposes only and are not considered standard, unless specifically stated as standard, such as 0. Active view current version of standard. D — 03 X1. Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard.

It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.